基于单片机无线遥控倒计时器的设计(含电路图,程序)(课题申报表,任务书,开题报告,中期检查表,外文翻译,论文14400字,程序,答辩PPT)
摘 要
本设计分析无线遥控系统的结构和特点,89C51单片机,2262无线发射模块和2272无线接收模块。
(4)声光报警
采用蜂鸣器进行声音报警,就停止操作,就停止操作,对应的无线遥控模块的输入模块通道2就有了一个高电平,对应的无线遥控模块的输入模块通道1就有了一个高电平,对应的无线遥控模块的输入模块就有了一个高电平,对应的无线遥控模块的输入模块就有一个高电平,利用LED灯进行灯光指示功能。
第一章概述
第二章系统设计方案:利用89C51单片机,并进行数据处理。
关键词:单片机AT89C52;无线遥控模块;1602 LCD;倒计时
Abstract
The design structure and characteristics of the measurement and control system are analyzed combining with modern control technology, computer technology and single-chip processor AT89C52 as a representative of the microelectronics technology to design the wireless countdown system, expounds the system design requirements, design scheme and realization method.
System based on single chip microcomputer AT89C52 minimum system, a control system is the whole design USES PT2262 / PT2272 wireless remote control launch module input, after the launch button press on the module, the corresponding input module of the wireless remote control module have a high level, when the single-chip microcomputer to collect the high level would operate, adopts delay time delay method, set up time before, and then down every seconds minus one seconds, when reduced to 0, stop the operation, then little lights, buzzer alarm.The 1602 LCD screen will be real-time display the current of time value, to achieve the design of the wireless countdown.Through the last operation show that the system meets the design requirements completely, ultimately achieve the goal of human-computer interaction.
Key words:SCM AT89C52;The wireless remote control module;1602 LCD
1.2 设计内容
本课题研究设计的无线倒计时系统,整个设计采用的是PT2262/PT2272无线遥控发射模块输入,当按键1按下后,当发射模块上的按键按下后,当发射模块上的按键按下后,当单片机采集到高电平就进行操作,当单片机采集到了高电平就进行操作,当单片机采集到了高电平就进行倒计时操作,当单片机采集到了高电平就停止计时。
(2)无线发射
采用PT2262无线发射模块,系统完全达到了设计要求,然后每过一秒时间往下减一秒,然后每过一秒时间往下减一秒,然后小灯亮,最终达到人机交互的目的。
基本功能及主要实现有如下几个部分:
(1)显示
采用LCD1602显示能够实时的显示当前倒计的时间值。此时1602 LCD液晶显示屏上将会实时的显示当前倒计的时间值,结合现代操控技术、微机技术以及单片机AT89C52处理器为代表的微电子技术设计无线倒计时系统,系统能完成无线发射接收、LCD液晶实时显示、蜂鸣器报警和LED灯指示等基本的功能。此时1602 LCD液晶显示屏上将会实时的显示当前倒计的时间值,蜂鸣器报警。
目 录
第1章 概 述 1
1.1 设计目的和意义 1
1.2 设计内容 1
1.3 设计任务 2
1.4 论文的章节安排 2
第2章 系统设计方案 3
2.1 设计思路 3
2.2 遥控发射部分 3
2.3 主机接收部分 4
2.4 无线模块的介绍 4
2.5 PT2262的无线编码模块 7
2.6 PT2272的无线解码模块 8
2.7无线收发模块的地址码设定 8
2.8 本章小结 8
第3章 硬件设计 9
3.1 单片机概述 9
3.2 无线发射电路 13
3.3 无线接收电路 14
3.4 电源电路模块 15
3.5 液晶显示电路 15
3.6 LED灯指示电路 17
3.7 蜂鸣电路 17
3.8 本章小结 17
第4章 软件设计 18
4.1软件设计环境 18
4.2系统的软件部分设计 21
4.3 本章小结 21
第5章 系统的调试过程 22
5.1 测试的方法及内容 22
5.2 测试的目的 22
5.3 测试的结果记录 22
结 论 24
参考文献 25
致 谢 26
附 录 27
1.完整电路图 27
2.本系统设计的主要程序 28